Gutter reattachment
Sagging gutters are rehung on solid fascia with new hangers with screws instead of loose spikes.
Exterior Services
Fascia Repair Midland Park, NJ
A Midland Park roofer can repair the fascia boards that carry your gutters and cap the ends of the rafters, and check the rafter tails behind the board while it is off. Dial (551) 370-0731 to talk with a local roofer about the fascia.
The fascia sits right where water leaves the roof, so it is the first trim board to rot when that water goes the wrong way. Clogged or poorly pitched gutters spill over the back, and a roof edge with no drip edge sends water straight down the fascia. Once the wood is soft, gutter hangers pull loose and the gutter sags or tips forward.
Fascia damage does not stay in the fascia for long. The same water rots the ends of the rafters, the first course of roof decking and the soffit nailer. Metal-wrapped fascia is especially tricky because water can get trapped behind the wrap and rot the wood out of sight.
It helps to know what you are seeing before you call. Look for sections where the gutter tips forward, where the board looks dark or swollen and where paint is flaking. Say whether the fascia is bare wood, painted, PVC or wrapped in metal, since that changes the repair.
Depending on what the roofer finds, fascia repair in Midland Park, NJ can go hand in hand with soffit repair and gutter installation.
Looking for Midland Park fascia repair? Call (551) 370-0731 and describe the problem to a roofer who works in Midland Park.
Call nowThe process
How fascia repair works
Here is how a roofer typically handles a fascia repair.
Inspect the roof edge
Before the board comes off, the roofer looks at what has been soaking it, from the shingle edge to the downspout. The length of the damage decides how much board is replaced.
Free the board
To reach the fascia, the gutter over it is removed and the hangers pulled. Old spikes and loose hangers are not reused.
Inspect behind the board
Soft rafter tails are cut back and sistered with new lumber, and rotted decking at the edge is replaced. This is the step that decides whether the repair lasts.
Fit the board
New fascia in primed wood, PVC or composite is cut to fit, with scarf joints at the seams. PVC and composite boards do not rot and hold paint well.
Close the gap
Drip edge flashing is slid under the shingles and over the gutter back, so water cannot reach the wood. Without it, the same board will rot again.
Finish the edge
The gutter goes back up with new hidden hangers screwed into solid wood, pitched toward the downspout. The board is painted to match if it is wood.
What is included
Fascia repairs a roofer can handle
Rafter tail repair
Soft framing at the roof edge is reinforced before the fascia goes back on.
Soft fascia
Soft wood along the roof edge is removed back to sound material and scarfed into the existing board.
Fascia wrapping
Metal wrap can be added over new or sound fascia to cut down on painting.
Drip edge installation
Missing or bent drip edge is replaced at the roof edge to keep runoff off the fascia.
Related service
Fascia Board Replacement Midland Park, NJ
Fascia board replacement means taking off whole lengths of board rather than patching short sections. With the old fascia off, every rafter end can be checked and repaired before the new boards are fastened. Many homeowners switch to PVC or composite fascia at this point because it will not rot.
In Midland Park, fascia board replacement often lines up with a new roof or new gutters, since the roof edge is already being worked on. Ask whether the roofer plans to remove the old boards or wrap over them, because wrapping soft wood only hides the rot. The new boards should match the old width so the soffit closes properly.
Related service
Fascia Board Repair Midland Park, NJ
Fascia board repair handles damage that is limited to a few spots, such as a rotted corner, the area under a leaky gutter seam or a section by a downspout. A scarf joint, cut at an angle and glued and fastened, blends the new piece into the old board and sheds water better than a square butt joint. Minor surface damage may only need consolidant, filler and paint.
Patching a fascia board in Midland Park without fixing the gutter or drip edge above it just buys a season or two. The cause is often a leaking gutter corner or a downspout that backs up. Sealed and painted, the patch holds up like the original wood.
Local help
Fascia Repair Near Me
In Midland Park, fascia tends to fail first on the sides of the house where gutters clog fastest. From Midland Park out to neighboring towns such as Waldwick, Ridgewood, Allendale and Glen Rock, older roof edges often need board and rafter tail repair while newer ones more often need drip edge and gutter fixes, which is why keeping gutters clear does so much to protect the fascia.
Need fascia repair around Midland Park? Call (551) 370-0731 for a Midland Park roofer who serves the towns around it too.
Roofs in this climate
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, which is how ice dams form and back water up under the shingles. Strong coastal storms push rain into every weak spot at the flashing and valleys. Most homeowners in Midland Park, NJ have the roof checked in the fall and again after the snow melts.
Why call
Why fix it now
Smaller repairs
A roof problem fixed early rarely spreads to the decking, the insulation or the ceilings.
Local knowledge
Local roofers see the same roofs and storm damage across Midland Park and nearby towns.
Know what happens next
Ask the roofer about the cause, the options and the estimate before work starts.
Fascia Repair FAQ
Should I cover rotted fascia with metal?
Metal wrap only belongs over sound wood. The gutter hangers still screw into the wood behind the wrap, so they loosen as the board softens. Wrap is a good finish over new or solid fascia.
Do I need new fascia boards or just a repair?
Spot repairs work well for rotted corners and short stretches. If the damage is widespread, new boards end up being the simpler fix. The roofer will probe the wood to see which option fits.
What is the best material for fascia?
PVC and composite fascia resist rot and hold paint well. Wood is common on older homes and works well when kept painted. No material holds up if water keeps running behind the gutter.
What causes fascia boards to rot?
Water getting behind the gutter is the main cause. Overflowing gutters, gutters pitched the wrong way and roof edges without drip edge soak the board repeatedly. Once the paint fails, the wood takes on water quickly.
Why do gutters pull away from the fascia?
A gutter is only as secure as the board behind it. As rot sets in, fasteners loosen and the gutter starts to droop under the weight of water and debris. The fix is solid wood plus new hangers, pitched toward the downspout.
More questions? Call (551) 370-0731
Often needed together
Soffit Repair
Repairs for rotted, sagging or loose soffit panels under the roof eaves, before rot spreads into the fascia and rafter tails.
Learn moreGutter Installation
Seamless gutter installation sized to the roof, pitched to the downspouts and hung on hidden hangers, so water ends up where it should.
Learn moreGutter Repair
Fixing gutters that drip at the corners, sag between hangers or pull away from the fascia, without replacing gutters that still have life in them.
Learn moreRoof Repair
Targeted roof repairs for wind, age and water damage, without replacing a roof that still has life left.
Learn more
Looking for something else?
See all roofing servicesTalk to a Midland Park roofer about fascia repair
Call now for Midland Park fascia repair and help in the towns around it.