Roof vents
Ridge vents or other exhaust paired with soffit intake which protects the roofing and the decking.
Roof Replacement
Roof Installation Midland Park, NJ
Installing a roof in Midland Park comes down to doing each layer in order, from the metal edges and underlayment to the flashing and the final ridge, whether the roof is going on a stripped deck or as a permitted overlay. Dial (551) 370-0731 to talk with a local roofer about installation.
When a fairly new roof leaks, the cause is usually how it was installed rather than what it was made of. Nails driven above the reinforced strip, flashing left out at a sidewall and short valleys are the kind of mistakes that show up within a few seasons. By the time they show up, the stain is already on the ceiling.
The first decision is what kind of roof to install. Architectural, or dimensional, asphalt shingles are the most common choice on houses, with thinner three-tab shingles still used on some homes and sheds, while standing seam or exposed fastener metal, concrete or clay tile and slate each need their own methods and fasteners. Roof pitch matters too, since standard shingles need enough slope to shed water and very low pitches call for a membrane instead.
Have some basics ready when you call. Say whether the job is a tear-off, an addition or new construction, and whether you have a material or color picked out.
Many roof installation calls in Midland Park also turn up a need for roof replacement or shingle roof installation.
Dealing with this in Midland Park, NJ right now? Call (551) 370-0731 to talk to a local roofer.
Call nowThe process
Steps in a roof installation
Here is the usual order for installing a shingle roof.
Prepare the deck
The roof deck must be clean, dry and solid, with any soft plywood or OSB replaced and loose boards renailed. Nails cannot hold in soft wood, so this step is never skipped.
Protect the eaves
Drip edge goes on at the eaves, ice and water shield is rolled out along the eaves and in the valleys, and drip edge is then added along the rakes over the underlayment. That layering lets water drain off the metal instead of behind it.
Underlayment install
The remaining deck is covered with underlayment, overlapped at the seams and fastened on the maker's pattern. It is the backup layer if a shingle is ever lifted or broken.
Set the flashing
Flashing goes in as the roofing goes up: step pieces at walls, a kickout at the bottom edge and boots on every pipe. Reused or caulk-only flashing is one of the most common installation shortcuts.
Install the roofing
After a starter course, the crew lays shingles row by row, keeping the exposure even and the nails inside the nail strip. In cold weather, shingles may need hand sealing because the sealant strips will not bond until warm sun hits them.
Ridge ventilation
The crew opens a slot at the ridge for a ridge vent, or installs box vents, and finishes with cap shingles. Balanced intake and exhaust keep the attic drier in winter and cooler in summer.
What is included
Components of the installation
Flashing
New flashing at every wall, chimney and vent pipe instead of reusing old metal.
Drip edge
Metal edges around the whole roof keeps water off the fascia boards.
Ice barrier
A full layer of underlayment plus ice barrier where water collects acts as the second layer of protection.
Roof covering
Starter strip, field shingles and ridge caps, or the panels and trim for a metal roof in straight, even courses.
Related service
New Roof Installation Midland Park, NJ
New roof installation covers three common jobs: replacing a roof after tear-off, roofing a new home and roofing an addition. Tie-ins between new and old roofs are a common leak point, so they need full ice barrier and careful flashing. Ask whether the new section will match the existing roofing or whether the whole roof should be redone.
Manufacturers publish exact steps for their products, and local code usually requires following them. A Midland Park roofer should be able to explain how many nails per shingle will be used, what underlayment goes down and what ventilation the attic will have. Vague answers about the hidden layers are worth noticing.
Related service
Roof Overlay Midland Park, NJ
An overlay skips the tear-off and lays new shingles over the current roof. It is only allowed on a roof with one existing layer that lies flat over a solid deck. It means less mess and a faster install.
There are good reasons most roofers prefer a tear-off. The deck stays hidden, ice barrier cannot be applied directly to the wood and any wear in the old roof shows through the new one. When an overlay is proposed, ask how they confirmed there is only one layer and how the flashing will be handled.
Local help
Roof Installation Near Me
Around Midland Park, roof installation work covers older houses getting their second or third roof and newer homes adding on. Across Midland Park and nearby places including Waldwick, Ridgewood, Allendale and Glen Rock, storms take the biggest toll on roofs that were installed with shortcuts, which is why the installation plan deserves as much attention as the material.
Need roof installation around Midland Park? Call (551) 370-0731 for a Midland Park roofer who serves the towns around it too.
How the weather here affects roofs around Midland Park
Cold winters bring snow, ice and a long stretch of freezing nights. When warm attic air melts the snow, the meltwater runs down and freezes again at the eaves, building ice dams that push water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. That is why roof repair in Midland Park is busiest after a hard winter and before the next one.
Why call
Why fix it now
Less damage
A roof problem fixed early rarely spreads to the decking, the insulation or the ceilings.
Roofers who know Midland Park
Local roofers see the same roofs and storm damage across Midland Park and nearby towns.
Clear next steps
Ask your questions before you agree to anything.
Roof Installation questions
What happens if a roof is installed in winter?
Winter installation is possible, with a few precautions. Crews keep shingles warm and may hand seal them, since the strips will not stick until the sun warms them. The deck has to be dry and free of frost.
How many days does roof installation take?
A typical house takes one to three working days once materials are on site. Steep pitches, many valleys and dormers, extra deck repair or a material like tile or standing seam metal take longer.
Which roofing material is best for my house?
That depends on the house, the slope of the roof and your priorities. Asphalt is the common choice, while metal, tile and slate each make sense for certain homes. A roofer can walk through the options for your specific roof.
Do I need a permit for roof installation?
Permit rules are set locally, and many places require one. Typically the contractor files it, and the town may inspect the finished roof.
What goes under a new roof?
The layers under the roofing are the drip edge, ice and water shield and a full layer of underlayment. Ask that the written scope lists each of these, not just the shingles.
More questions? Call (551) 370-0731
Often needed together
Roof Replacement
Full tear-off and replacement for roofs that are worn out, storm beaten or leaking in several places, with the old layers removed and the deck checked.
Learn moreShingle Roof Installation
New shingle roofs built layer by layer on a sound deck, with nailing and flashing done to the shingle instructions.
Learn moreMetal Roof Installation
New metal roofs in standing seam, exposed fastener, metal shingle and stone coated steel, for homes, garages and outbuildings.
Learn moreNew Construction Roofing
New construction roofs coordinated with the builder's schedule, so the house is protected before interior work starts.
Learn more
Looking for something else?
See all roofing servicesTalk to a Midland Park roofer about roof installation
Call (551) 370-0731 to talk to a roofer serving Midland Park, NJ.